Schema 18W Audio AmplifierDiagram
Saturday, October 17, 2009
Useful Schema 18W Audio AmplifierDiagram
Circuit diagram:
18 Watt Amplifier
Amplifier parts:
P1_____________22K Log. Potentiometer (Dual-gang for stereo)
R1______________1K 1/4W Resistor
R2______________4K7 1/4W Resistor
R3____________100R 1/4W Resistor
R4______________4K7 1/4W Resistor
R5_____________82K 1/4W Resistor
R6_____________10R 1/2W Resistor
R7_______________R22 4W Resistor (wirewound)
R8______________1K 1/2W Trimmer Cermet (optional)
C1____________470nF 63V Polyester Capacitor
C2,C5_________100µF 3V Tantalum bead Capacitors
C3,C4_________470µF 25V Electrolytic Capacitors
C6____________100nF 63V Polyester Capacitor
D1___________1N4148 75V 150mA Diode
IC1________TLE2141C Low noise, high voltage, high slew-rate Op-amp
Q1____________BC182 50V 100mA NPN Transistor
Q2____________BC212 50V 100mA PNP Transistor
Q3___________TIP42A 60V 6A PNP Transistor
Q4___________TIP41A 60V 6A NPN Transistor
J1______________RCA audio input socket
Power supply parts:
R9______________2K2 1/4W Resistor
C7,C8________4700µF 25V Electrolytic Capacitors
D2_____________100V 4A Diode bridge
D3_____________5mm. Red LED
T1_____________220V Primary, 15 + 15V Secondary, 50VA Mains transformer
PL1____________Male Mains plug
SW1____________SPST Mains switch
* Can be directly connected to CD players, tuners and tape recorders.
* Do not exceed 23 + 23V supply.
* Q3 and Q4 must be mounted on heatsink.
* D1 must be in thermal contact with Q1.
Technical data:
Output power:
18 Watt RMS into 8 Ohm (1KHz sine wave)
Sensitivity:
150mV input for 18W output
Frequency response:
30Hz to 20KHz -1dB
Total harmonic distortion @ 1KHz:
0.1W 0.02% 1W 0.01% 5W 0.01% 10W 0.03%
Total harmonic distortion @10KHz:
0.1W 0.04% 1W 0.05% 5W 0.06% 10W 0.15%
Unconditionally stable on capacitive loads
Circuit diagram:
18 Watt Amplifier
Amplifier parts:
P1_____________22K Log. Potentiometer (Dual-gang for stereo)
R1______________1K 1/4W Resistor
R2______________4K7 1/4W Resistor
R3____________100R 1/4W Resistor
R4______________4K7 1/4W Resistor
R5_____________82K 1/4W Resistor
R6_____________10R 1/2W Resistor
R7_______________R22 4W Resistor (wirewound)
R8______________1K 1/2W Trimmer Cermet (optional)
C1____________470nF 63V Polyester Capacitor
C2,C5_________100µF 3V Tantalum bead Capacitors
C3,C4_________470µF 25V Electrolytic Capacitors
C6____________100nF 63V Polyester Capacitor
D1___________1N4148 75V 150mA Diode
IC1________TLE2141C Low noise, high voltage, high slew-rate Op-amp
Q1____________BC182 50V 100mA NPN Transistor
Q2____________BC212 50V 100mA PNP Transistor
Q3___________TIP42A 60V 6A PNP Transistor
Q4___________TIP41A 60V 6A NPN Transistor
J1______________RCA audio input socket
Power supply parts:
R9______________2K2 1/4W Resistor
C7,C8________4700µF 25V Electrolytic Capacitors
D2_____________100V 4A Diode bridge
D3_____________5mm. Red LED
T1_____________220V Primary, 15 + 15V Secondary, 50VA Mains transformer
PL1____________Male Mains plug
SW1____________SPST Mains switch
* Can be directly connected to CD players, tuners and tape recorders.
* Do not exceed 23 + 23V supply.
* Q3 and Q4 must be mounted on heatsink.
* D1 must be in thermal contact with Q1.
* Quiescent current (best measured with an Avo-meter in series with Q3 Emitter) is not critical.
* Adjust R3 to read a current between 20 to 30 mA with no input signal.
* To facilitate quiescent current setting add R8 (optional).
* A correct grounding is very important to eliminate hum and ground loops. Connect to the same point the ground sides of J1, P1, C2, C3 & C4. Connect C6 to the output ground.
* Then connect separately the input and output grounds to the power supply ground.
* Adjust R3 to read a current between 20 to 30 mA with no input signal.
* To facilitate quiescent current setting add R8 (optional).
* A correct grounding is very important to eliminate hum and ground loops. Connect to the same point the ground sides of J1, P1, C2, C3 & C4. Connect C6 to the output ground.
* Then connect separately the input and output grounds to the power supply ground.
Technical data:
Output power:
18 Watt RMS into 8 Ohm (1KHz sine wave)
Sensitivity:
150mV input for 18W output
Frequency response:
30Hz to 20KHz -1dB
Total harmonic distortion @ 1KHz:
0.1W 0.02% 1W 0.01% 5W 0.01% 10W 0.03%
Total harmonic distortion @10KHz:
0.1W 0.04% 1W 0.05% 5W 0.06% 10W 0.15%
Unconditionally stable on capacitive loads
